Compex LinkPort ENET-C Guida di Installazione Pagina 43
- Pagina / 140
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Installation 43
On switches running CatOS, you can only change channel mode per module. In the following example,
change the channel mode for slots 1 and 2 by using the following command:
set channelprotocol lacp module_number
Verify the changes by using the following command:
show channelprotocol.
CatOSSwitch (enable) set channelprotocol lacp 1
Mod 1 is set to LACP protocol.
CatOSSwitch (enable) set channelprotocol lacp 2
Mod 2 is set to LACP protocol.
CatOSSwitch (enable) show channelprotocol
Channel
Module Protocol
------- --------
1 LACP
2 LACP
3 PAGP
5 PAGP
On switches running Cisco IOS Software, specify which interfaces should be using LACP by entering the
following interface configuration command:
channel-protocol lacp:
CiscoIOSSwitch(config-if)#channel-protocol lacp
Example switch configuration of a Cat 6500 switch using IOS. Ports 7/46, 7/47, and 7/48 on the Cat
6500 switch are used to uplink to the Virtual Connect module:
interface Port-channel10
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
no ip address
interface GigabitEthernet7/46
description test-VC
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
no ip address
speed 1000
channel-protocol lacp
channel-group 10 mode active
!
interface GigabitEthernet7/47
description test-VC
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
no ip address
speed 1000
channel-protocol lacp
channel-group 10 mode active
!
interface GigabitEthernet7/48
description test-VC
- Setup and Installation Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Documentation resources 6
- Planning the installation 7
- Pre-deployment planning 8
- Planning the installation 9 9
- Hardware setup overview 10
- Default module configuration 11
- Installation 13
- Supported configurations 14
- Bay configuration guidelines 17
- Installation 20 20
- Virtual Connect and EBIPA 21
- Network loop protection 24
- Installation 25 25
- Installation 26 26
- Installation 27 27
- Installation 28 28
- Installation 29 29
- Installing a VC-Enet module 30
- Installation 33 33
- Installing a VC-FC module 35
- Factory default settings 38
- Installation 43 43
- Failover and check-pointing 44
- Virtual Connect modules 45
- VC-FC module 49
- HP Virtual Connect Manager 50
- Deployment 51
- Running the setup wizards 54
- Local Enclosure 55
- Enclosure Import/Recovery 56
- Enclosure Import 58
- Enclosure recovery 59
- General Settings 60
- Local Users 61
- • Upper-case character 62
- • Lower-case character 62
- • Numeric character 62
- Finish domain wizard 64
- MAC Address Settings 65
- Server VLAN Tag Settings 68
- Define Single Network 71
- Advanced Network Settings 72
- Defined Network Connections 76
- Finish network wizard 76
- WWN settings 78
- Assigned WWNs 80
- Define Fabric 81
- Define SAN Fabric 82
- Defined SAN Fabric 83
- Finish Fibre Channel wizard 83
- Serial Number Settings 85
- Assign Server Profiles 87
- • Single enclosure domain 88
- Name Server Profiles 89
- Create Server Profiles 90
- Verify link and speed 92
- Component identification 93
- Item Description Status 94
- Shared port operation 100
- Switch Default Function 101
- Item Description 106
- HP 4Gb VC-FC Module LEDs 107
- NPIV) components and LEDs 109
- Module components and LEDs 112
- FCC rating label 119
- Modifications 120
- • EMC Directive 2004/108/EC 121
- Japanese notice 122
- BSMI notice 122
- Korean notice 122
- Chinese notice 123
- Laser compliance 123
- Electrostatic discharge 124
- Support and other resources 125
- Customer Self Repair 127
- Reparo feito pelo cliente 129
- Acronyms and abbreviations 133
- World Wide Name 135
- Documentation feedback 136
- Index 137 137
- Index 138 138
- Index 139 139
- Index 140 140
Prodotti e manuali riguardandi Networking Compex LinkPort ENET-C
Networking Compex LinkPort ENET-C Manuale Utente
(28 pagine)
(28 pagine)
Networking Compex SCSI TO S-ATA RAID Specifiche
(258 pagine)
(258 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale